Skip to content
English
  • There are no suggestions because the search field is empty.

Where do I see my search criteria, and how do I check how my location was interpreted?

Your criteria appear on the Current Criteria card at the bottom of the AI Advisor chat. Check it before you click Count or Go.

Your search criteria appear on the Current Criteria card at the bottom of the AI Advisor chat, in the left panel. Check it before you click Count or Go to confirm ParGo understood your request, especially the location.

Using an older guide that mentions a criteria box in the top-left of the map? That floating box was removed in V3.0 and replaced by the Current Criteria card. Use the steps below instead.

Where your criteria appear

The AI Advisor is the left panel, beside the map, with results on the right. On mobile it opens as a bottom sheet. When you describe a search in plain English, the Advisor turns it into filters and shows them on the Current Criteria card at the bottom of the chat, below the latest message. The card scrolls with the chat, and nothing runs until you click Count or Go.

  1. Type your request in the AI Advisor, for example "DDA or QCT parcels in Santa Clara city, CA".
  2. Scroll to the Current Criteria card. Each filter is a chip that reads field, operator and value, for example "Land use is Commercial".
  3. Click Count to see how many parcels match. The number appears next to the button.
  4. Click Go to run the search and show the parcels on the map. The card stays in the chat with a green Active badge. Go stays greyed out until you change the criteria.
On the card What it does
× on a chip Removes that filter
Sliders icon (Edit filters) Opens Prompt Helper
Clear all Removes every filter
Save / Load Saves the criteria, or loads saved criteria
Count / Go Counts matches, or runs the search

Each Advisor reply that builds or changes a search also shows a collapsed Updated: … line. Expand it to see the criteria from that point in the conversation, and click Adopt this criteria to load them back onto the card. Then click Go to run them again.

Check how your location was interpreted

The location chip on the Current Criteria card shows the geography ParGo will search. Before you click Go, check that it names:

  • The place you meant. For example, the city and not a county or region with a similar name.
  • The right state, if the chip shows one. Many city names exist in several states.
  • Every place you listed. In a multi-city request, each city should appear.

You can't edit a location chip in place. If it's wrong, remove it with its × and rephrase your request in the chat with the county and state, for example "Santa Clara city, Santa Clara County, CA". Then check the card again. Clicking Count first is a quick way to see whether the number of parcels looks right for that area.

Add or adjust criteria with Prompt Helper

Prompt Helper (called Prompt Builder in V4.2) replaced the old pop-out criteria block. Use it when you aren't sure which field or wording to use.

  1. Click ? Prompt Helper just above the chat input, or the sliders icon (Edit filters) on the Current Criteria card. On desktop it opens as a panel to the right of the Advisor.
  2. Search fields by keyword and add one to your criteria, or browse suggested prompts by the kind of work. Prompts you've starred appear here too (new in V4.6).
  3. To limit the search to the area on screen, turn on Restrict to Current Map View at the top of Prompt Helper. The chip Geography In current map view appears on the card.
  4. Check the Current Criteria card again before you click Count or Go.

Save and reuse criteria

  1. Click Save on the Current Criteria card.
  2. Type a name under Criteria name and click Save. If you loaded saved criteria and changed them, you can click Update instead.
  3. Find your saved criteria on the Criteria tab of your dashboard, or click Load on the card to bring them back.

Saving criteria isn't available on trial accounts.

If results fall outside your area

Results outside your area usually mean the location was read more broadly than you intended. Two common causes are a city name that exists in several states, or a multi-city request where the boundary wasn't applied to every city.

  • Name the county and state. Remove the location chip, run the search again with both named, then check the new chip.
  • Use the map instead. Pan and zoom to the exact area, open Prompt Helper and turn on Restrict to Current Map View, then click Go. Only parcels inside the visible map are returned.
  • Check the Meets Criteria tab. Results are split into Meets Criteria, Added by You, Enriched and Removed, so parcels you added by hand aren't mixed in with the search results.

Still stuck?

Use the Get Support form in the app or the customer portal, chat with ParGo Pal on pargoai.com, or email support@pargoai.com. Include your exact search wording and a screenshot of the Current Criteria card.